配置文件使用说明
<h2>特别注意用英文输入法!注意标点符号!</h2>
<h3>配置文件在conf\npc.conf文件里,使用文本文档编辑</h3>
<h4>一:需要修改的地方,<code>有蓝色标注!</code></h4>
<table>
<thead>
<tr>
<th style="text-align: left;">[common]</th>
<th>这里不要修改</th>
</tr>
</thead>
<tbody>
<tr>
<td style="text-align: left;"><code>server_addr=</code></td>
<td>这里填frp服务器的地址+端口号客服会给你</td>
</tr>
<tr>
<td style="text-align: left;"><code>vkey=</code></td>
<td>这里填你的密钥,16位随机英文数字</td>
</tr>
<tr>
<td style="text-align: left;">conn_type=</td>
<td>tcp(这里不要改)</td>
</tr>
<tr>
<td style="text-align: left;">disconnect_timeout=</td>
<td>60(连接超时时间,默认60秒)</td>
</tr>
</tbody>
</table>
<h4>单端口tcp示例</h4>
<table>
<thead>
<tr>
<th style="text-align: left;">[<code>tcp</code>]</th>
<th>名称,随机改个英文或数字即可,3位以上</th>
</tr>
</thead>
<tbody>
<tr>
<td style="text-align: left;"><code>mode=</code></td>
<td>tcp(连接方式tcp就写tcp)</td>
</tr>
<tr>
<td style="text-align: left;"><code>target_addr=</code></td>
<td>127.0.0.1:8080(127.0.0.1为本机,8080本地服务的运行端口)</td>
</tr>
<tr>
<td style="text-align: left;"><code>server_port=</code></td>
<td>10001(远程端口号,改为分配你的端口</td>
</tr>
</tbody>
</table>
<h4>单端口udp示例</h4>
<table>
<thead>
<tr>
<th style="text-align: left;">[<code>udp</code>]</th>
<th>名称,随机改个英文或数字即可,3位以上</th>
</tr>
</thead>
<tbody>
<tr>
<td style="text-align: left;"><code>mode=</code></td>
<td>udp(连接方式udp就写udp)</td>
</tr>
<tr>
<td style="text-align: left;"><code>target_addr=</code></td>
<td>127.0.0.1:8211(127.0.0.1为本机,8080本地服务的运行端口)</td>
</tr>
<tr>
<td style="text-align: left;"><code>server_port=</code></td>
<td>10002(远程端口号,改为分配你的端口</td>
</tr>
</tbody>
</table>
<p>单端口示例</p>
<pre><code>[common]
server_addr=frpa01.ntpizza.com:10000
conn_type=tcp
vkey=1234567812345678
disconnect_timeout=60
[tcp]
mode=tcp
target_addr=127.0.0.1:8080
server_port=10001
[udp]
mode=udp
target_addr=127.0.0.1:8211
server_port=10002</code></pre>